Effect Of Sea Moisture Content On Corrosion Hull Of A Warship Made By PT Pal Indonesia
Abstract
Seawater temperature ranges from -2 0 c to 300 c. Low temperatures are usually found in seawater
around the poles and on the deep seabed. Meanwhile, high seawater temperatures are found in the sea
in the Arid area. The Red Sea and Bab El Mandeb have temperatures of about 290 c to 300. Corrosion
is a subject matter that concerns various disciplines, or in other words, it connects elements of physics,
chemistry, metallurgy, electronics and engineering. This study uses the literature review study method
to collect, identify, evaluate the effect of seawater content on the corrosion of the hulls of warships
made by PT Pal Indonesia. An effective corrosion control strategy should be selected with the selection
of suitable coatings for the marine environment. Hull plating with paint has a special function to protect
the construction of the hull, especially those located below the waterline and the construction of the
ship above the waterline.
Downloads
References
Athanasius Priharyoto Bayuseno (2009) Analysis Of Corrosion Rate In Steel For Ship Materials With And
Without Paint Protection, Journal Of Mechanical Engineering, Diponegoro University Vol. 11 No. 3.
Budi Utomo (2009) Types Of Corrosion And Its Countermeasures. Journal Of Marine Science And
Technology Vol. 6 No. 2.
Choirul Huda., Dwi Heru Sutjahjo(2017)Corrosion Rate Analysis Of Aluminum Material 5083 As An
Application Of Ship Hull Materials. Journal Of Surabaya State University Vol.6 No. 2.
Diky Ilham, Gyani Ubaydillah, Nani Mulyaningsih, Catur Pramono (2019) The Effect Of Adding Guava Leaf
Extract Inhibitors On Corrosion Rate On Ship Dapra Chains, Merc Journal Of Mechanical Engineering Vol. 2
No. 1.
Eko Julianto Sasono (2010) The Effectiveness Of The Use Of Aluminum Alloy Victim Anodes On The Steel
International Journal of Science, Technology & Management ISSN: 2722 - 4015
Plates Of The Aisi E 2512 Ship Against Corrosion Rates In Seawater Media. Mechanical Engineering,
Diponegoro University.
Faizal Dwi Saputro (2017) Variations In Corrosion Media And Timing Of Corrosion Rates In Low-Carbon Steel
Metals (Mild Steel) By Modeling The Condition Of Ship Steering Fins, Journal Of Mechanical Engineering
Unesa Vol. 5 No. 3.
Nani Mulyaningsih, Sigit Mujiarto, Gyani (2019) Influence Of Guava Leaves As Inhibitors Of Natural Corrosion
Of Ship Chains Department Of Mechanical Engineering, Tidar University Journal Of Mechanical Engineering,
Vol. 3, No. 1, P-Issn: 2598-7380 E-Issn: 2613-9847.
M. Rafee Revaldi Marcell, Heri Supomo, Mohammad Sholikhan Arif (2021) Technical And Economic Analysis
Of The Corrosion Rate Comparison Of Galvanized Steel And Aluminum Materials To Predict The Life And
Cost Of Hull Repairs, Its Engineering Journal Vol.10 No. 2
Ngatmin Ngatmin, Helmy Purwanto, Indah Sejarahi (2019) Corrosion Rate Analysis Of The Hull Steel Plate
With Aluminum Victim Anode Bait. Faculty Of Engineering, Wahid Hasyim University Vol. 15 No. 2.
Rista Andini (2017) Analysis Of The Corrosion Rate Of Metal Kunungan (Brass) As An Application Of Ship
Propeller Materials, Journal Of Mechanical Engineering Vol. 5 No 2.
Sri Endah Susilowati, Didit Sumardiyanto (2018) Application Of Marine Growth Prevention System (Mgps) In
Ship Operations To Inhibit The Corrosion Rate, Journal Of Technology, Muhammadiya University Jakarta
Vol. 10 No. 2.
Satria Nova M. K, Mohammad Nurul Misbah (2012) Analysis Of The Effect Of Salinity And Seawater
Temperature On The Corrosion Rate Of A36 Steel In Smaw Welding, Its Engineering Journal Vol. 1 No. 1.
Sutrisno Lilik Budiyanto (2021) The Effect Of Seawater Salinity On The Corrosion Rate On The Hull Plate Of A
Dwt Ship. Journal Of Nautical Dynamics Vol. 2 No.1 Issn: 2087-3050 E-Issn: 2722-0621.
Tri Karyono, Budianto, Reza Gadis Pamungkas (2017) Analysis Of Corrosion Prevention Techniques On The
Hull With Variations In The Iccp Prevention System Compared To Sacp. Journal Of Professional Education
Vol. 6 No. 1.
Yudha Kurniawan Afandi, Irfan Syarif Arief, Amiadji Amiadji (2015) Analysis Of Corrosion Rate In Carbon
Steel Plates With Variations In Coating Thickness. Its Engineering Journal Vol 4. No.1..
